10 film chip capacitors pet-ht dielectric ? cb series general description film chip capacitor using a naked and stacked construction with metallized high temperature pet (polyethylene terephtalate). advantages ? use of high temperature dielectric films makes these capacitors suitable for ir or vapor phase reflow processes. this chip is built without specific encapsulation. ? the intrinsic elasticity of the dielectric film allows an excellent compatibility of the capacitor with all types of material for printed circuit boards. ? the self-healing property of film technology results to a safety open failure mode and better overall reliability. ? excellent thermal shock resistance. ? low dissipation factor esr & esl. ? no piezoelectric effect. ? available in tape and reel suitable for automatic placement. ? non-polar construction. outer layer termination plating : 100% matte sn ni barrier under termination silver epoxy resin brass active layers : pet dielectric applications general purpose function in low voltage applications where miniaturization and smd is required. typical applications would be: ? automotive (airbag, fuel injection calculator...) ? telecom (public switching systems, modems, telephone set, cordless, mobile) ? industrial (smps, power convertor module...) performance characteristics climatic category 55/125/56 capacitance range 10nf to 4.7f tolerance on c r 5%, 10% nominal voltages 63vdc to 630vdc test voltage 1.4vr 2 sec. at 25c soldering methods ir or vapor phase reflow (not suitable for wave soldering) tangent of loss angle at 1khz (df) < 100 x 10 -4 insulation resistance minimum : ir for c 0.33f ir > 1000 m at 20c for 1 min. charge at 10vdc for vr < 100vdc and 100vdc for vr 100vdc for c > 0.33f ir c > 400 sec. at 20c for 1 min. charge at 10vdc for vr < 100vdc and 100vdc for vr 100vdc temperature range -55c to 125c with voltage derating of 1.25%/c between 105c and 125c a.c. applications for high frequency a.c. application please check with avx
11 film chip capacitors pet-ht dielectric ? cb series capacitance values (cr) and nominal voltages (vr) voltage vdc: 63v vac: 40v capacitance chip dimensions reel range ordering *tolerances tape dimensions reel dimensions packaging unit pkg (cr) code (page 6) code l w h max t w p1 k0 a w1 w2 max b ulk reel 0.270f cb042d0274+ -- 5.8 5.0 2.8 0.8 12.0 8.0 3.1 330 12.4 18.4 1500 3000 bc (0.228) (0.195) (0.110) (0.032) (0.472) (0.315) (0.122) (12.99) (0.488) (0.724) 0.330f cb042d0334+ -- 5.80 5.00 3.30 0.80 12.0 8.00 3.45 330 12.4 18.4 1500 2800 bc (0.228) (0.195) (0.130) (0.032) (0.472) (0.315) (0.136) (12.99) (0.488) (0.724) 0.390 cb042d0394++ -- 5.80 5.00 3.40 0.80 12.0 8.00 3.45 330 12.4 18.4 1500 2800 bc (0.228) (0.195) (0.134) (0.032) (0.472) (0.315) (0.136) (12.99) (0.488) (0.724) 0.470 cb042d0474+ -- 5.80 5.00 3.50 0.80 12.0 8.00 4.10 330 12.4 18.4 1500 2300 bc (0.228) (0.195) (0.138) (0.032) (0.472) (0.315) (0.162) (12.99) (0.488) (0.724) 0.560 cb042d0564+ -- 5.80 5.00 3.50 0.80 12.0 8.00 4.10 330 12.4 18.4 1500 2300 bc (0.228) (0.195) (0.138) (0.032) (0.472) (0.315) (0.162) (12.99) (0.488) (0.724) 0.680 cb042d0684+ -- 5.80 5.00 4.00 0.80 12.0 8.00 4.10 330 12.4 18.4 1500 2300 bc (0.228) (0.195) (0.158) (0.032) (0.472) (0.315) (0.162) (12.99) (0.488) (0.724) 0.820 cb052d0824+ -- 7.2 6.1 3.7 0.8 24.0 12 3.8 330 24.4 30.4 1000 2250 bc (0.283) (0.24) (0.146) (0.032) (0.944) (0.472) (0.149) (12.99) (0.96) (1.196) 1f cb052d0105+ -- 7.2 6.1 3.7 0.8 24.0 12 3.8 330 24.4 30.4 1000 2250 bc (0.283) (0.24) (0.146) (0.032) (0.944) (0.472) (0.149) (12.99) (0.96) (1.196) 1.5 cb052d0155+ -- 7.20 6.10 5.30 0.80 16.0 12.0 5.50 330 16.4 22.4 1000 1000 bc (0.283) (0.240) (0.209) (0.032) (0.629) (0.472) (0.216) (12.99) (0.645) (0.881) 2.2 CB162D0225+ -- 10.5 7.6 5.8 0.8 24.0 12 6.19 330 24.4 30.4 500 900 bc (0.413) (0.299) (0.229) (0.032) (0.944) (0.472) (0.244) (12.99) (0.96) (1.196) 3.3 cb172d0335+ -- 12.8 10.2 5.50 0.80 24.0 16.0 5.70 330 24.4 30.4 300 700 bc (0.503) (0.401) (0.216) (0.032) (0.944) (0.629) (0.224) (12.99) (0.961) (1.196) 4.7f cb182d0475+ -- 15.3 13.7 4.90 0.80 24.0 24.0 5.50 330 24.4 30.4 300 500 bc (0.601) (0.539) (0.193) (0.032) (0.944) (0.944) (0.216) (12.99) (0.961) (1.196) voltage vdc: 100v vac: 63v 0.180f cb042e0184+ -- 5.8 5.0 2.3 0.8 12.0 8.0 2.43 330 12.4 18.4 1500 3500 bc (0.228) (0.195) (0.091) (0.032) (0.472) (0.315) (0.096) (12.99) (0.488) (0.724) 0.220f cb042e0224+ -- 5.80 5.00 3.30 0.80 12.0 8.00 3.45 330 12.4 18.4 1500 3000 bc (0.228) (0.195) (0.130) (0.032) (0.472) (0.315) (0.136) (12.99) (0.488) (0.724) 0.270f cb042e0274 +-- 5.8 5.0 3.4 0.8 12.0 8.0 3.45 330 12.4 18.4 1500 2800 bc (0.228) (0.195) (0.134) (0.032) (0.472) (0.315) (0.136) (12.99) (0.488) (0.724) 0.330 cb042e0334+ -- 5.80 5.00 4.00 0.80 12.0 8.00 4.10 330 12.4 18.4 1500 2300 bc (0.228) (0.195) (0.158) (0.032) (0.472) (0.315) (0.161) (12.99) (0.488) (0.724) 0.390 cb042e0394+ -- 5.80 5.00 3.90 0.80 12.0 8.00 4.10 330 12.4 18.4 1500 2300 bc (0.228) (0.195) (0.154) (0.032) (0.472) (0.315) (0.161) (12.99) (0.488) (0.724) 0.470 cb042e0474+ -- 5.80 5.00 4.30 0.80 12.0 8.0 4.50 330 12.4 18.4 1500 1900 bc (0.228) (0.195) (0.169) (0.032) (0.472) (0.315) (0.177) (12.99) (0.488) (0.724) 0.560 cb052e0564+ -- 7.20 6.10 4.20 0.80 16.0 12.0 4.80 330 16.4 22.4 1000 1800 bc (0.283) (0.240) (0.165) (0.032) (0.629) (0.472) (0.189) (12.99) (0.645) (0.881) 0.680 cb052e0684+ -- 7.20 6.10 5.00 0.80 16.0 12.0 5.23 330 16.4 22.4 1000 1100 bc (0.283) (0.240) (0.197) (0.032) (0.629) (0.472) (0.206) (12.99) (0.645) (0.881) 0.820 cb052e0824+ -- 7.20 6.10 4.70 0.80 16.0 12.0 4.80 330 16.4 22.4 1000 1800 bc (0.283) (0.240) (0.185) (0.032) (0.629) (0.472) (0.189) (12.99) (0.645) (0.881) 1f cb052e0105+ -- 7.20 6.10 5.70 0.80 16.0 12.0 5.90 330 16.4 22.4 1000 900 bc (0.283) (0.240) (0.224) (0.032) (0.629) (0.472) (0.232) (12.99) (0.645) (0.881) 1.5 cb162e0155+ -- 10.5 7.60 6.10 0.80 24.0 12.0 6.19 330 24.4 30.4 500 900 bc (0.413) (0.299) (0.240) (0.032) (0.944) (0.472) (0.244) (12.99) (0.961) (1.196) replace the + by the tolerance code: j = 5% or k = 10% replace the -- by the packaging suffix: -- = bulk bc = tape & reel millimeters (inches) w l h t
12 film chip capacitors pet-ht dielectric ? cb series capacitance values (cr) and nominal voltages (vr) voltage vdc: 100v vac: 63v capacitance chip dimensions reel range ordering *tolerances tape dimensions reel dimensions packaging unit pkg (cr) code (page 6) code l w h max t w p1 k0 a w1 w2 max b ulk reel 2.2 cb172e0225+ -- 12.8 10.2 5.50 0.80 24.0 16.0 5.70 330 24.4 30.4 300 700 bc (0.503) (0.401) (0.216) (0.032) (0.944) (0.629) (0.224) (12.99) (0.961) (1.196) 3.3 cb182e0335+ -- 15.3 13.7 5.20 0.80 24.0 24.0 5.50 330 24.4 30.4 300 500 bc (0.601) (0.539) (0.204) (0.032) (0.944) (0.944) (0.216) (12.99) (0.961) (1.196) 4.7f cb182e0475+ -- 15.3 13.7 7.10 0.80 24.0 24.0 7.60 330 24.4 30.4 300 300 bc (0.601) (0.539) (0.279) (0.032) (0.944) (0.944) (0.299) (12.99) (0.961) (1.196) voltage vdc: 250v vac: 160v 0.047f cb042g0473+ -- 5.80 5.00 3.00 0.80 12.0 8.00 3.10 330 12.4 18.4 1500 3000 bc (0.228) (0.195) (0.118) (0.032) (0.472) (0.315) (0.122) (12.99) (0.488) (0.724) 0.056 cb042g0563+ -- 5.80 5.00 3.60 0.80 12.0 8.00 4.10 330 12.4 18.4 1500 2300 bc (0.228) (0.195) (0.142) (0.032) (0.472) (0.315) (0.161) (12.99) (0.488) (0.724) 0.068 cb042g0683+ -- 5.80 5.00 4.00 0.80 12.0 8.00 4.10 330 12.4 18.4 1500 2300 bc (0.228) (0.195) (0.158) (0.032) (0.472) (0.315) (0.161) (12.99) (0.488) (0.724) 0.082 cb042g0823+ -- 5.80 5.00 4.00 0.80 12.0 8.00 4.10 330 12.4 18.4 1500 2300 bc (0.228) (0.195) (0.158) (0.032) (0.472) (0.315) (0.161) (12.99) (0.488) (0.724) 0.1f cb042g0104+ -- 5.80 5.00 4.00 0.80 12.0 8.00 4.10 330 12.4 18.4 1500 2300 bc (0.228) (0.195) (0.158) (0.032) (0.472) (0.315) (0.161) (12.99) (0.448) (0.724) 0.120 cb052g0124+ -- 7.20 6.10 4.30 0.80 16.0 12.0 4.80 330 16.4 22.4 1000 1800 bc (0.283) (0.240) (0.169) (0.032) (0.629) (0.472) (0.189) (12.99) (0.645) (0.881) 0.150 cb052g0154+ -- 7.20 6.10 4.30 0.80 16.0 12.0 4.80 330 16.4 22.4 1000 1800 bc (0.283) (0.240) (0.169) (0.032) (0.629) (0.472) (0.189) (12.99) (0.645) (0.881) 0.180 cb052g0184+ -- 7.20 6.10 5.10 0.80 16.0 12.0 5.23 330 16.4 22.4 1000 1100 bc (0.283) (0.240) (0.200) (0.032) (0.629) (0.472) (0.206) (12.99) (0.645) (0.881) 0.220 cb052g0224+ -- 7.20 6.10 4.90 0.80 16.0 12.0 5.23 330 16.4 22.4 1000 1100 bc (0.283) (0.240) (0.193) (0.032) (0.629) (0.472) (0.206) (12.99) (0.645) (0.881) 0.270 cb162g0274+ -- 10.5 7.60 4.80 0.80 24.0 12.0 6.19 330 24.4 30.4 500 1100 bc (0.413) (0.299) (0.189) (0.032) (0.944) (0.472) (0.244) (12.99) (0.961) (1.196) 0.330 cb162g0334+ -- 10.5 7.60 5.60 0.80 24.0 12.0 6.19 330 24.4 30.4 500 900 bc (0.413) (0.299) (0.220) (0.032) (0.944) (0.472) (0.244) (12.99) (0.961) (1.196) 0.390 cb162g0394+ -- 10.5 7.60 5.40 0.80 24.0 12.0 6.19 330 24.4 30.4 500 900 bc (0.413) (0.299) (0.213) (0.032) (0.944) (0.472) (0.244) (12.99) (0.961) (1.196) 0.470 cb162g0474+ -- 10.5 7.6 6.15 0.80 24.0 12.0 6.19 330 24.4 30.4 500 900 bc (0.413) (0.299) (0.241) (0.032) (0.944) (0.472) (0.244) (12.99) (0.961) (1.196) 0.560 cb172g0564+ -- 12.8 10.2 5.60 0.80 24.0 16.0 5.70 330 24.4 30.4 300 700 bc (0.503) (0.402) (0.220) (0.032) (0.944) (0.629) (0.225) (12.99) (0.961) (1.196) 0.680 cb172g0684+ -- 12.8 10.2 6.50 0.80 24.0 16.0 7.00 330 24.4 30.4 300 600 bc (0.503) (0.402) (0.255) (0.032) (0.944) (0.629) (0.275) (12.99) (0.961) (1.196) 0.820 cb182g0824+ -- 15.3 13.7 5.10 0.80 24.0 24.0 5.50 330 24.4 30.4 300 500 bc (0.601) (0.539) (0.201) (0.032) (0.944) (0.944) (0.217) (12.99) (0.961) (1.196) 1f cb182g0105+ -- 15.3 13.7 6.00 0.80 24.0 24.0 6.30 330 24.4 30.4 300 400 bc (0.601) (0.539) (0.236) (0.032) (0.944) (0.944) (0.248) (12.99) (0.961) (1.196) 1.5 cb182g0155+ -- 15.3 13.7 7.00 0.80 24.0 24.0 7.60 330 24.4 30.4 300 300 bc (0.601) (0.539) (0.276) (0.0315) (0.944) (0.944) (0.299) (12.99) (0.961) (1.196) replace the + by the tolerance code: j = 5% or k = 10% replace the -- by the packaging suffix: -- = bulk bc = tape & reel millimeters (inches) w l h t
13 film chip capacitors pet-ht dielectric ? cb series capacitance values (cr) and nominal voltages (vr) voltage vdc: 400v vac: 200v capacitance chip dimensions reel range ordering *tolerances tape dimensions reel dimensions packaging unit pkg (cr) code (page 6) code l w h max t w p1 k0 a w1 w2 max b ulk reel 0.010f cb042i0103+ -- 5.80 5.00 3.00 0.80 12.0 8.00 3.10 330 12.4 18.4 1500 3000 bc (0.228) (0.195) (0.017) (0.032) (0.472) (0.315) (0.122) (12.99) (0.488) (0.724) 0.012 cb042i0123+ -- 5.80 5.00 2.40 0.80 12.0 8.00 2.43 330 12.4 18.4 1500 3500 bc (0.228) (0.195) (0.095) (0.032) (0.472) (0.315) (0.096) (12.99) (0.488) (0.724) 0.015 cb042i0153+ -- 5.80 5.00 4.00 0.80 12.0 8.00 4.10 330 12.4 18.4 1500 2300 bc (0.228) (0.195) (0.158) (0.032) (0.472) (0.315) (0.161) (12.99) (0.488) (0.724) 0.018 cb052i0183+ -- 7.2 6.1 2.8 0.8 16.0 12 3.8 330 16.4 22.4 1000 2250 bc (0.283) (0.240) (0.110) (0.032) (0.629) (0.472) (0.150) (12.99) (0.645) (0.881) 0.022 cb052i0223+ -- 7.2 6.1 3.5 0.8 16.0 12 3.8 330 16.4 22.4 1000 2250 bc (0.283) (0.240) (0.138) (0.032) (0.629) (0.472) (0.150) (12.99) (0.645) (0.881) 0.027 cb052i0273+ -- 7.2 6.1 2.8 0.8 16.0 12 3.8 330 16.4 22.4 1000 2250 bc (0.283) (0.240) (0.110) (0.032) (0.629) (0.472) (0.150) (12.99) (0.645) (0.881) 0.033 cb052i0333+ -- 7.2 6.1 3.3 0.8 16.0 12 3.8 330 16.4 22.4 1000 2250 bc (0.283) (0.240) (0.130) (0.032) (0.629) (0.472) (0.150) (12.99) (0.645) (0.881) 0.047 cb052i0473+ -- 7.20 6.10 4.50 0.80 16.0 12.0 4.80 330 16.4 22.4 1000 1800 bc (0.283) (0.240) (0.177) (0.032) (0.629) (0.472) (0.189) (12.99) (0.645) (0.881) 0.056 cb162i0563+ -- 10.5 7.60 3.10 0.80 24.0 12.0 3.93 330 24.4 30.4 500 1400 bc (0.413) (0.299) (0.122) (0.032) (0.944) (0.472) (0.155) (12.99) (0.961) (1.196) 0.068 cb162i0683+ -- 10.5 7.60 3.60 0.80 24.0 12.0 3.93 330 24.4 30.4 500 1400 bc (0.413) (0.299) (0.141) (0.032) (0.944) (0.472) (0.155) (12.99) (0.961) (1.196) 0.082 cb162i0823+ -- 10.5 7.60 4.20 0.80 24.0 12.0 6.19 330 24.4 30.4 500 900 bc (0.413) (0.299) (0.165) (0.032) (0.944) (0.472) (0.244) (12.99) (0.961) (1.196) 0.100f cb162i0104+ -- 10.5 7.60 4.70 0.80 24.0 12.0 6.19 330 24.4 30.4 500 900 bc (0.413) (0.299) (0.185) (0.032) (0.944) (0.472) (0.244) (12.99) (0.961) (1.196) 0.120 cb172i0124+ -- 12.8 10.2 3.90 0.80 24.0 16.0 4.00 330 24.4 30.4 300 1100 bc (0.503) (0.402) (0.154) (0.032) (0.944) (0.629) (0.157) (12.99) (0.961) (1.196) 0.150 cb172i0154+ -- 12.8 10.2 4.60 0.80 24.0 16.0 4.70 330 24.4 30.4 300 900 bc (0.503) (0.402) (0.181) (0.032) (0.944) (0.629) (0.185) (12.99) (0.961) (1.196) 0.180 cb172i0184+ -- 12.8 10.2 5.60 0.80 24.0 16.0 7.00 330 24.4 30.4 300 600 bc (0.503) (0.402) (0.220) (0.032) (0.944) (0.629) (0.274) (12.99) (0.961) (1.196) 0.220 cb172i0224+ -- 12.8 10.2 6.80 0.80 24.0 16.0 7.00 330 24.4 30.4 300 600 bc (0.503) (0.402) (0.265) (0.032) (0.944) (0.629) (0.274) (12.99) (0.961) (1.196) 0.270 cb172i0274+ -- 12.8 10.2 6.80 0.80 24.0 16.0 7.00 330 24.4 30.4 300 600 bc (0.503) (0.402) (0.265) (0.032) (0.944) (0.629) (0.274) (12.99) (0.961) (1.196) 0.330 cb182i0334+ -- 15.3 13.7 5.60 0.80 24.0 24.0 6.30 330 24.4 30.4 300 400 bc (0.601) (0.539) (0.220) (0.032) (0.944) (0.944) (0.248) (12.99) (0.961) (1.196) 0.470f cb182i0474+ -- 15.3 13.7 6.20 0.80 24.0 24.0 6.30 330 24.4 30.4 300 400 bc (0.601) (0.539) (0.244) (0.032) (0.944) (0.944) (0.248) (12.99) (0.961) (1.196) voltage vdc: 630v vac: 250v 0.010f cb042k0103+ -- 5.80 5.00 2.80 0.80 12.0 8.00 3.10 330 12.4 18.4 1500 3000 bc (0.228) (0.195) (0.110) (0.032) (0.472) (0.315) (0.122) (12.99) (0.488) (0.724) 0.012 cb042k0123+ -- 5.80 5.00 3.30 0.80 12.0 8.00 3.10 330 12.4 18.4 1500 2800 bc (0.228) (0.195) (0.130) (0.032) (0.472) (0.315) (0.122) (12.99) (0.488) (0.724) 0.015 cb042k0153+ -- 5.80 5.00 4.00 0.80 12.0 8.00 4.10 330 12.4 18.4 1500 2300 bc (0.228) (0.195) (0.158) (0.032) (0.472) (0.315) (0.161) (12.99) (0.488) (0.724) 0.018 cb052k0183+ -- 5.80 6.10 2.80 0.80 24.0 12.0 3.80 330 24.4 30.4 1000 2250 bc (0.228) (0.240) (0.110) (0.032) (0.944) (0.472) (0.149) (12.99) (0.961) (1.196) replace the + by the tolerance code: j = 5% or k = 10% replace the -- by the packaging suffix: -- = bulk bc = tape & reel millimeters (inches) w l h t
14 film chip capacitors pet-ht dielectric ? cb series capacitance values (cr) and nominal voltages (vr) voltage vdc: 630v vac: 250v capacitance chip dimensions reel range ordering *tolerances tape dimensions reel dimensions packaging unit pkg (cr) code (page 6) code l w h max t w p1 k0 a w1 w2 max b ulk reel 0.022 cb052k0223+ -- 7.20 6.10 3.50 0.80 24.0 12.0 3.80 330 24.4 30.4 1000 2250 bc (0.283) (0.240) (0.138) (0.032) (0.944) (0.472) (0.149) (12.99) (0.961) (1.196) 0.027 cb052k0273+ -- 7.20 6.10 4.10 0.80 16.0 12.0 4.80 330 16.4 22.4 1000 1800 bc (0.283) (0.240) (0.161) (0.032) (0.629) (0.472) (0.189) (12.99) (0.645) (0.881) 0.033 cb052k0333+ -- 7.20 6.10 5.00 0.80 16.0 12.0 4.80 330 16.4 22.4 1000 1100 bc (0.283) (0.240) (0.197) (0.032) (0.629) (0.472) (0.189) (12.99) (0.645) (0.881) 0.047 cb162k0473+ -- 10.5 7.60 3.60 0.80 24.0 12.0 3.93 330 24.4 30.4 500 1400 bc (0.413) (0.299) (0.141) (0.032) (0.944) (0.472) (0.155) (12.99) (0.961) (1.196) 0.056 cb162k0563+ -- 10.5 7.60 4.30 0.80 24.0 12.0 6.19 330 24.4 30.4 500 900 bc (0.413) (0.299) (0.169) (0.032) (0.944) (0.472) (0.244) (12.99) (0.961) (1.196) 0.068 cb162k0683+ -- 10.5 7.60 5.20 0.80 24.0 12.0 6.19 330 24.4 30.4 500 900 bc (0.413) (0.299) (0.205) (0.032) (0.944) (0.472) (0.244) (12.99) (0.961) (1.196) 0.082 cb172k0823+ -- 12.8 10.2 4.30 0.80 24.0 16.0 4.70 330 24.4 30.4 300 900 bc (0.503) (0.402) (0.169) (0.032) (0.944) (0.629) (0.185) (12.99) (0.961) (1.196) 0.100f cb172k0104+ -- 12.8 10.2 5.00 0.80 24.0 16.0 5.70 330 24.4 30.4 300 700 bc (0.503) (0.402) (0.197) (0.032) (0.944) (0.629) (0.225) (12.99) (0.961) (1.196) 0.120 cb172k0124+ -- 12.8 10.2 5.60 0.80 24.0 16.0 5.70 330 24.4 30.4 300 700 bc (0.503) (0.402) (0.220) (0.032) (0.944) (0.629) (0.225) (12.99 ) (0.961) (1.196 ) 0.150 cb172k0154+ -- 12.8 10.2 6.90 0.80 24.0 16.0 7.00 330 24.4 30.4 300 600 bc (0.503) (0.402) (0.271) (0.032) (0.944) (0.629) (0.275) (12.99 ) (0.961) (1.196 ) 0.180 cb182k0184+ -- 15.3 13.7 5.00 0.80 24.0 24.0 5.50 330 24.4 30.4 300 500 bc (0.601) (0.539) (0.197) (0.032) (0.944) (0.944) (0.217) (12.99) (0.961) (1.196) 0.220 cb182k0224+ -- 15.3 13.7 5.80 0.80 24.0 24.0 6.30 330 24.4 30.4 300 400 bc (0.601) (0.539) (0.229) (0.032) (0.944) (0.944) (0.248) (12.99) (0.961) (1.196) 0.270f cb182k0274+ -- 15.3 13.7 7.20 0.80 24.0 24.0 7.60 330 24.4 30.4 300 300 bc (0.601) (0.539) (0.284) (0.032) (0.944) (0.944) (0.299) (12.99) (0.961) (1.196) replace the + by the tolerance code: j = 5% or k = 10% replace the -- by the packaging suffix: -- = bulk bc = tape & reel millimeters (inches) w l h t
15 film chip capacitors pet-ht dielectric ? cb series mounting and soldering recommendations *reflow soldering referring to jedec standard with some limitations *jedec j-std 020c soldering profile the capacitors can be mounted using infrared and vapor phase soldering following recommended below. they are not suitable for wave soldering. all temperature refer to topside of the package, measured on the package body surface. recommended solder paste thickness profile feature 2220 to 2824 4030 to 6054 ramp-up (t s max to t p ) 3c / second max 3c / second max preheat - temperature min (t s min) 150c 150c - temperature min (t s max) 200c 200c - time (t s min to t s max) 180 sec. max 180 sec. max time maintained above - temperature (t l ) 217c 217c - time (t l ) 60 sec. max 75 sec. max peak temperature (t p ) 240c 245c time within 5c of peak 10 sec. 10 sec. temperature (t p ) ramp-down 6c / sec. 6c / sec. for optimum solderability, the recommended soldering paste thickness: 2220 to 2824 :150 to 200m 4030 to 6054 :200 to 300m in case of hand soldering, the temperature of the soldering iron should not be above 250c. special care must be taken to avoid touching the capacitor body with the iron tip. size code case size a b c 04 2220 5.00 (0.195) 1.90 (0.075) 4.50 (0.178) 05 2824 6.00 (0.234) 2.50 (0.098) 5.70 (0.224) 16 4030 7.50 (0.295) 3.00 (0.118) 8.00 (0.315) 17 5040 11.2 (0.441) 3.50 (0.137) 10.3 (0.406) 18 6064 14.6 (0.575) 3.60 (0.147) 12.6 (0.496) pad dimensions: millimeters (inches) a cb recommended cleaning to clean flux from the pc board assembly, the recommended products are: ethanol, isopropyl alcohol, and deionized water wash. the cleaning products to avoid are: toluene, xylene, trichloroethylene, terpene cleaner ec-7, surface active agent. in case of using another solvent, please contact us. other cautions flame retardancy: the dielectric film is not a flame retardant material. environment: contact us when chips are used in humid or gas atmosphere and /or when using resin. recommended handling: do not use edged tools, so not to damage the capacitors. tin whiskers tests : jedec standard no 22a121 stress type ref. spec. test conditions analysis results temperature cycling jesd22-a104 -55c +85(+10/-0)c air sem x 1000 pass 5 to 10 minutes soak 3 cycles/hour ambient temperature / 30+/-2c - 60+/-3% rh -2000h sem x 1000 pass humidity storage high temperature / 70+/-5c - 93+3/-2% rh -1000h sem x 1000 pass humidity storage 030 time (seconds) temperature (?) 60 90 120 150 180 210 240 ramp down ramp up 270 300 330 t p t p - 5? t s min t s max t l t s t p t l
16 film chip capacitors pet-ht dielectric ? cb series electrical characteristics versus temperature and frequency electrical characteristics 10 8 6 4 2 0 -2 -4 -6 -8 c/c vs temperature temperature -55?c -30?c -5?c +20?c +45?c +70?c +95?c +120?c 10000.0 1000.0 100.0 10.0 1.0 0.1 ir(g.ohm) temperature ir vs temperature 100nf -55?c -30?c -5?c +20?c +45?c +70?c +95?c +120?c 160 140 120 100 80 60 40 20 0 dc/c = (temperature) temperature df (1khz) vs temperature -55?c -30?c -5?c +20?c +45?c +70?c +95?c +120?c d.f. (10 -4 ) capacitance dissipation factor insulation resistance frequency characteristics 4 3 2 1 0 -1 -2 -3 -4 -5 0.1 1 10 100 1000 c/c 20 c (%) frequency (khz) 1000.00 100.00 10.00 1.00 1.00 10.00 frequency (mhz) z (mohm) 1 f 470 nf 220 nf 47 nf 100 nf 4.7 ? 400 300 200 100 0 10 100 1000 1 0.1 df 20 c (10 ) -4 frequency (khz) capacitance dissipation factor impedance
17 film chip capacitors pet-ht dielectric ? cb series rms voltage and current versus frequency maximum voltage (vrms) and current (irms) vs frequency typical curves results from measurement carried out at ambient temperature (25oc) and sinusoidal wave-forms (for size cb04 to cb18) 0 5 10 15 20 25 30 35 40 45 0.1 1 10 100 1000 10000 frequency (khz) v rms (v) 4.7? 1.5? 0.47? 0 20 40 60 80 100 120 140 160 180 0.1 1 10 100 1000 10000 frequency (khz) v rms (v) 1f 0.47f 0.1f 0 10 20 30 40 50 60 70 0.1 1 10 100 1000 10000 frequency (khz) v rms (v) 4.7f 1.5f 0.22f 63v dc / 40 v ac 100 v dc / 63 v ac 250 v dc / 160 v ac 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 0.1 1 10 100 1000 10000 i rms (a) 4.7f 1.5f 0.47f frequency (khz) 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 0.1 1 10 100 1000 10000 frequency (khz) i rms (a) 1f 0.47f 0.1f 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 0.1 1 10 100 1000 10000 frequency (khz) i rms (a) 4.7f 1.5f 0.22f 63v dc / 40 v ac 100 v dc / 63 v ac 250 v dc / 160 v ac
18 film chip capacitors pet-ht dielectric ? cb series rms voltage and current versus frequency maximum pulse rise time ( d v/ dt ) maximum voltage (vrms) and current (irms) vs frequency typical curves results from measurement carried out at ambient temperature (25oc) and sinusoidal wave-forms (for size cb04 to cb18) 0 20 40 60 80 100 120 140 160 180 200 220 0.1 1 10 100 1000 10000 frequency (khz) v rms (v) 0.47f 0.1f 0.01f 0 0.5 1 0.1 1 10 100 1000 10000 frequency (khz) i rms (a) 0.47f 0.1f 0.01f 400 v dc / 200 v ac 400 v dc / 200 v ac 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 0.1 1 10 100 1000 10000 frequency (khz) v rms (v) 0.27f 0.1f 0.01f 0 0.5 1 0.1 1 10 100 1000 10000 frequency (khz) i rms (a) 0.27f 0.1f 0.01f 630 v dc / 250 v ac 630 v dc / 250 v ac voltage range 63 100 250 400 630 dv/dt max. 40 50 150 200 250 (v/sec)
19 film chip capacitors pet-ht dielectric ? cb series ? rohs materials controlled by rohs (ppm by weight): mass / unit (g) lead mercury cadmium hexavalent pbb pbde chromium cb range 000 0 00 rohs limit (ppm) 1000 1000 100 1000 1000 1000 pass/fail pass pass pass pass pass pass this product has been tested and found to be compliant with all requirements, provisions, and exemptions of eu directive 2002/9 5/ec of the european parliament and council of january 27, 2003. on the restriction of use of certain hazardous substances (rohs) in electrical and electronic equi pment and eu directive 2000/53/ec regarding elv or end of life vehicle. rohs / elv status external plating 100% matte sn as standard lead-free status / moisture sensitivity ranking pb free reflow solder compliant, msl = 3. reflow soldering referring to jedec standard with some limitations. additional jesd-97 data to be phased in msl e3 termination. product labeling: (for informational purposes only to be phased in on reel and container.) product traceability: full internal material traceability by reference to unique lot number marked on reel and external package. rohs compliant: pb free:
|
